裁線條碼亮燈

出自TSK WIKI
於 2019年1月4日 (五) 13:36 由 Root​(留言 | 貢獻) 所做的修訂 (→20190113)
跳至導覽 跳至搜尋

20190104

<c> //20190104增加流水燈

  1. include <usbhid.h>
  2. include <usbhub.h>
  3. include <hiduniversal.h>
  4. include <hidboot.h>
  5. include <SPI.h>
  6. include <FastLED.h>
  1. define NUM_LEDS 60 // led灯数量
  2. define DATA_PIN 6 // 数据传输引脚(Digital 6)
  3. define BRIGHTNESS 25 //設定led亮度

int LIGHTDELAY= 60/NUM_LEDS/60; String s; CRGB leds[NUM_LEDS];

class MyParser : public HIDReportParser {

 public:
   MyParser();
   void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf);
 protected:
   uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key);
   virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key);
   virtual void OnScanFinished();

};

MyParser::MyParser() {}

void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) {

 // If error or empty, return
 if (buf[2] == 1 || buf[2] == 0) return;

 for (uint8_t i = 7; i >= 2; i--) {
   // If empty, skip
   if (buf[i] == 0) continue;

   // If enter signal emitted, scan finished
   if (buf[i] == UHS_HID_BOOT_KEY_ENTER) {
     OnScanFinished();
   }

   // If not, continue normally
   else {
     // If bit position not in 2, it's uppercase words
     OnKeyScanned(i > 2, buf, buf[i]);
   }

   return;
 }

}

uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) {

 // Letters
 if (VALUE_WITHIN(key, 0x04, 0x1d)) {
   if (upper) return (key - 4 + 'A');
   else return (key - 4 + 'a');
 }

 // Numbers
 else if (VALUE_WITHIN(key, 0x1e, 0x27)) {
   return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1');
 }

 if(key== 55 ) { 
   return 46; 
   }else return 0;

}

void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) {

 uint8_t ascii = KeyToAscii(upper, mod, key);
// Serial.print((char)ascii);  
delay(100);
 s= s + ((char)ascii) + "";

}

void MyParser::OnScanFinished() {

 int i,k,j=2;
 
 float a=s.toFloat();
 a=a*60;
 int uplimit=ceil(a)-1;
 int downlimit=floor(a)-1;
 //Serial.println(uplimit);  
 FastLED.clear();

 for(i=1;i< downlimit;i++){
   leds[i] = CRGB::Yellow;
   FastLED.show();
   delay(LIGHTDELAY);
   FastLED.clear();
 }


 if(uplimit==downlimit){
   leds[uplimit] = CRGB::White;
 }else{
   leds[uplimit] = CRGB::Red;  // 设置第1个led灯的颜色Red
   leds[downlimit] = CRGB::Green;  // 设置第2个led灯的颜色Red
 }
 FastLED.show();
 s="";
 

}

USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser;

void setup() {

 FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯
 FastLED.setBrightness(  BRIGHTNESS );
 Serial.begin( 115200 );
 Serial.println("Start");

 if (Usb.Init() == -1) {
   Serial.println("OSC did not start.");
 }

 delay( 200 );

 Hid.SetReportParser(0, &Parser);

}

void loop() {

 Usb.Task();

}

</c>

20190103

<c>

  1. include <usbhid.h>
  2. include <usbhub.h>
  3. include <hiduniversal.h>
  4. include <hidboot.h>
  5. include <SPI.h>
  6. include <FastLED.h>
  1. define NUM_LEDS 60 // led灯数量
  2. define DATA_PIN 6 // 数据传输引脚(Digital 6)
  3. define BRIGHTNESS 25 ////設定led亮度

String s; CRGB leds[NUM_LEDS];

class MyParser : public HIDReportParser {

 public:
   MyParser();
   void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf);
 protected:
   uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key);
   virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key);
   virtual void OnScanFinished();

};

MyParser::MyParser() {}

void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) {

 // If error or empty, return
 if (buf[2] == 1 || buf[2] == 0) return;
 for (uint8_t i = 7; i >= 2; i--) {
   // If empty, skip
   if (buf[i] == 0) continue;
   // If enter signal emitted, scan finished
   if (buf[i] == UHS_HID_BOOT_KEY_ENTER) {
     OnScanFinished();
   }
   // If not, continue normally
   else {
     // If bit position not in 2, it's uppercase words
     OnKeyScanned(i > 2, buf, buf[i]);
   }
   return;
 }

}

uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) {

 // Letters
 if (VALUE_WITHIN(key, 0x04, 0x1d)) {
   if (upper) return (key - 4 + 'A');
   else return (key - 4 + 'a');
 }
 // Numbers
 else if (VALUE_WITHIN(key, 0x1e, 0x27)) {
   return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1');
 }
 if(key== 55 ) { 
   return 46; 
   }else return 0;
 

}

void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) {

 uint8_t ascii = KeyToAscii(upper, mod, key);
// Serial.print((char)ascii);  
delay(100);
 s= s + ((char)ascii) + "";

//s=s + ascii; }

void MyParser::OnScanFinished() {

 float a=s.toFloat();
 a=a*60;
 int uplimit=ceil(a)-1;
 int downlimit=floor(a)-1;
 Serial.println(uplimit);  
 FastLED.clear();
 if(uplimit==downlimit){
   leds[uplimit] = CRGB::White;
 }else{
   leds[uplimit] = CRGB::Red;  // 设置第1个led灯的颜色Red
   leds[downlimit] = CRGB::Green;  // 设置第2个led灯的颜色Red
 }
 FastLED.show();
 s="";

}

USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser;

void setup() {

 FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯
 FastLED.setBrightness(  BRIGHTNESS );
 Serial.begin( 115200 );
 Serial.println("Start");
 if (Usb.Init() == -1) {
   Serial.println("OSC did not start.");
 }
 delay( 200 );
 Hid.SetReportParser(0, &Parser);

}

void loop() {

 Usb.Task();

} </c>