「HYTREL製程改善」:修訂間差異

出自TSK WIKI
跳至導覽 跳至搜尋
Tpl​(留言 | 貢獻)
Tpl​(留言 | 貢獻)
第6行: 第6行:
**二段230 -> 240
**二段230 -> 240
**三段240 -> 250
**三段240 -> 250
*眼模
*眼模
**內眼模2.7mm -> <span style="color:red">2.9mm</span>
**內眼模2.7mm -> <span style="color:red">2.9mm</span>
第26行: 第27行:
**https://dl.dropboxusercontent.com/s/kuvzjx3ndw86knv/PDFXEdit_2016-12-29_16-19-35.png
**https://dl.dropboxusercontent.com/s/kuvzjx3ndw86knv/PDFXEdit_2016-12-29_16-19-35.png
**[http://www.erocarb.ch/ja/%E3%82%B5%E3%83%BC%E3%83%93%E3%82%B9/%E3%83%81%E3%83%83%E3%83%97%E5%8F%8A%E3%81%B3%E3%83%80%E3%82%A4%E3%82%B9%E3%81%AE%E8%A8%88%E7%AE%97 DDR網頁計算公式]
**[http://www.erocarb.ch/ja/%E3%82%B5%E3%83%BC%E3%83%93%E3%82%B9/%E3%83%81%E3%83%83%E3%83%97%E5%8F%8A%E3%81%B3%E3%83%80%E3%82%A4%E3%82%B9%E3%81%AE%E8%A8%88%E7%AE%97 DDR網頁計算公式]
*DRB
*DRB
**(2.7/0.7)/(1.5/0.4)=1.03
**(2.7/0.7)/(1.5/0.4)=1.03
**(2.7/0.7)/(1.5/0.4)=1.105
**(2.7/0.7)/(1.5/0.4)=1.105
**https://dl.dropboxusercontent.com/s/vpimijbzuoe2nmh/PDFXEdit_2016-12-29_17-06-21.png
**https://dl.dropboxusercontent.com/s/vpimijbzuoe2nmh/PDFXEdit_2016-12-29_17-06-21.png
*模具計算
*模具計算
**[[檔案:DDR Ratio.png]]
**[[檔案:DDR Ratio.png]]
第36行: 第39行:
**IF DDR=20 THEN Tip OD = √20 * 0.4 = 1.79
**IF DDR=20 THEN Tip OD = √20 * 0.4 = 1.79
**[http://www.bhtool.com/advisor-article2.htm 原文]
**[http://www.bhtool.com/advisor-article2.htm 原文]
*模具可能造成的影響
 
**[http://www.bhtool.com/index.html]
*[http://www.bhtool.com/index.html 模具可能造成的影響]


==杜邦技術資料==
==杜邦技術資料==

於 2016年12月30日 (五) 10:36 的修訂

20161229

  • 溫度
    • 機頭260 -> 270
    • 洩料250 -> 260
    • 一段220 -> 230
    • 二段230 -> 240
    • 三段240 -> 250
  • 眼模
    • 內眼模2.7mm -> 2.9mm
    • 外眼模0.6mm/1.5mm ->
  • 間格 1 -> 0
  • 連動 -> 連動(原連動調不到轉速,廠長指導後可用連動)
  • 螺旋轉速rpm 21.7 -> 46.8
  • 引取轉速rpm 476 -> 551
  • 線速120 -> 145
  • 外徑測定器0.73 -> 0.73
  • 導体預熱 off -> 微溫40A/5.5V
  • 真空吸引 -> 0.45
  • DRB
    • (2.7/0.7)/(1.5/0.4)=1.03
    • (2.7/0.7)/(1.5/0.4)=1.105
    • PDFXEdit_2016-12-29_17-06-21.png
  • 模具計算
    • IF DDR=20 THEN Die ID = √20 * 0.7 = 3.13
    • IF DDR=20 THEN Tip OD = √20 * 0.4 = 1.79
    • 原文

杜邦技術資料

  • (L/D) ratio ideally 24:1
  • The optimum draw-down ratio (D.D.R.) is in the range of 5–20:1
  • The extruder die should be between 2 and 3 times the required tube outside diameter
  • Vacuum of 0.10 to 0.30 bar has been used successfully to maintain
  • PDFXEdit_2016-12-29_16-14-03.png
  • PDFXEdit_2016-12-29_16-13-16.png
  • PDFXEdit_2016-12-29_16-13-34.png