「HYTREL製程改善」:修訂間差異
跳至導覽
跳至搜尋
新頁面: ==20161229== *溫度 **機頭260 -> 270 **洩料250 -> 260 **一段220 -> 230 **二段230 -> 240 **三段240 -> 250 *眼模 **內眼模2.7mm -> **外眼模0.6/1.5mm -> *間格 1 ->... |
|||
| 第20行: | 第20行: | ||
**(2.7^2-1.5^2)/(0.7^2-0.4^2)=15.27 -> | **(2.7^2-1.5^2)/(0.7^2-0.4^2)=15.27 -> | ||
**(2.9^2-1.5^2)/(0.7^2-0.4^2)=18.67 | **(2.9^2-1.5^2)/(0.7^2-0.4^2)=18.67 | ||
**https://dl.dropboxusercontent.com/s/byocji4mi7p6emy/PDFXEdit_2016-12-29_16-11-48.png | |||
**https://dl.dropboxusercontent.com/s/kuvzjx3ndw86knv/PDFXEdit_2016-12-29_16-19-35.png | |||
==杜邦技術資料== | |||
*(L/D) ratio ideally 24:1 | |||
* The optimum draw-down ratio (D.D.R.) is in the range of 5–20:1 | |||
*The extruder die should be between 2 and 3 times the required tube outside diameter | |||
*Vacuum of 0.10 to 0.30 bar has been used successfully to maintain | |||
*https://dl.dropboxusercontent.com/s/oblg3nmbcs1liu1/PDFXEdit_2016-12-29_16-14-03.png | |||
* https://dl.dropboxusercontent.com/s/p2dmfg4sci5zth9/PDFXEdit_2016-12-29_16-13-16.png | |||
*https://dl.dropboxusercontent.com/s/cc5e4ixxg47xys8/PDFXEdit_2016-12-29_16-13-34.png | |||
* | |||
於 2016年12月29日 (四) 16:24 的修訂
20161229
- 溫度
- 機頭260 -> 270
- 洩料250 -> 260
- 一段220 -> 230
- 二段230 -> 240
- 三段240 -> 250
- 眼模
- 內眼模2.7mm ->
- 外眼模0.6/1.5mm ->
- 間格 1 ->
- 連動 -> 單動
- 螺旋轉速rpm 21.7 -> 46.8
- 引取轉速rpm 476 -> 551
- 線速120 -> 145
- 外徑測定器0.73 -> 0.73
- 導体預熱 off -> 微溫40A/5.5V
- 真空吸引 -> 0.45
- DDR
- (2.7^2-1.5^2)/(0.7^2-0.4^2)=15.27 ->
- (2.9^2-1.5^2)/(0.7^2-0.4^2)=18.67


杜邦技術資料
- (L/D) ratio ideally 24:1
- The optimum draw-down ratio (D.D.R.) is in the range of 5–20:1
- The extruder die should be between 2 and 3 times the required tube outside diameter
- Vacuum of 0.10 to 0.30 bar has been used successfully to maintain


