「Robot-TOP電線研發規劃」:修訂間差異

出自TSK WIKI
跳至導覽 跳至搜尋
Root​(留言 | 貢獻)
Root​(留言 | 貢獻)
第258行: 第258行:
** Unaged: 100% 10.3MPa
** Unaged: 100% 10.3MPa
** Aged: 65% 75%
** Aged: 65% 75%
==單芯線測試項目==
*Basic tests:
*Physical Properties Unaged and Air Oven Aged, Section 14.
*Conductor Corrosion Test, Section 18
*Deformation Test (Thermoplastics and Class XL Only), Section 19.
*Flexibility Test, Section. 21.
*Heat Shock Test (Thermoplastic Materials Only), Section 22.
*Cold Bend Test, Section 23.
*Durability of Ink-Print Test, Section 27
*Crush Resistance Test, Section 28.
*Dielectric Test, Method I, Section 29.
*Dielectric Test, Method II, Section 30.
*Dielectric Test, Method III, Section 31.
*Horizontal Flame Test for Internal Wiring, Section 40.


==20160719==
==20160719==

於 2016年8月11日 (四) 18:21 的修訂

HYTREL體積抵抗率(單位:ohm m)

  • HY8238:2.0E+14
  • HY6356:8.0E+11
  • HY5556:4.0E+11
  • IHV-9851N:1.0E+11
  • IHV-9874N:1.0E+11

HYTREL認證

  • Hytrel® DuPont
    • 承茂專員:吳文傑(Jack Wu) jack.wu@chinmou.com.tw
    • Thermoplastic elastomer
    • TPES (UL style no Material)
    • TPC-ET(歐規)
  • Style no. 10912 (Northwire used)
  • 認證規劃:
    • Style 10912 105℃ 600V 8mil(0.203mm),未來通用於600V及300V
    • Style 10140 80℃ 30V 2mil(0.051mm),未來使用於30V,如捲線厚度0.15t

尼龍絕緣被覆NYLON

相關的TPES,TPE 單芯線

style Insulation it_min cond_min cond_max temp volts Flame remark
10042 TPES 8 32 AWG 2 AWG 80 300ac None
10140 TPES 2 42 AWG n/a 80 30ac None
11097 TPE 3 44 AWG 10 AWG 105 30ac None
11098 TPE 6 44 AWG 10 AWG 105 300ac None
10282 TPES 5 42 AWG n/a 90 90ac None IGUS
10263 TPES 12 32 AWG 4/0 AWG 80 600, 1000ac None
10264 TPES 16 32 AWG 4/0 AWG 80 1000ac None
10390 TPES 10 36 AWG 4/0 AWG 80 600ac None
10903 TPES 8 44 AWG 6 AWG 60 300ac Horizontal
10904 TPES 8 44 AWG 6 AWG 60 600ac Horizontal
10907 TPES 8 44 AWG 6 AWG 80 300ac Horizontal
10908 TPES 8 44 AWG 6 AWG 80 600ac Horizontal
10909 TPES 8 44 AWG 6 AWG 105 30ac Horizontal
10910 TPES 8 44 AWG 6 AWG 105 150ac Horizontal
10911 TPES 8 44 AWG 6 AWG 105 300ac Horizontal
10912 TPES 8 44 AWG 6 AWG 105 600ac Horizontal
10666 TPE 9 30 AWG 6 AWG 105 600ac None 日合
11104 TPES 8 44 AWG 6 AWG 105 600ac Horizontal
11105 TPES 8 44 AWG 6 AWG 105 300ac Horizontal
11169 TPES 30 50 AWG 10 AWG 125 600ac None

阻燃替代方案

  • 原欲申請TPES
    • 10140
    • 10912
  • 改申請TPE(限定使用在cable內;非單心線販售)
    • 11097
    • 11098
    • 10666
  • TPE UL 1581 Table 50.223,50.224
    • TPE designates an extensible compound whose characteristic constituent is a themoplastic elastomer.
    • Unaged: 200% 5.52MPa
    • Aged: 75% 75%
  • TPES UL 1581 Table 50.226
    • TPES designates a compounded thermoplastic material whose characteristic constituent is a polyester such as PBT or PET, their individual copolymers, blends of any of these.
    • Unaged: 100% 10.3MPa
    • Aged: 65% 75%

單芯線測試項目

  • Basic tests:
  • Physical Properties Unaged and Air Oven Aged, Section 14.
  • Conductor Corrosion Test, Section 18
  • Deformation Test (Thermoplastics and Class XL Only), Section 19.
  • Flexibility Test, Section. 21.
  • Heat Shock Test (Thermoplastic Materials Only), Section 22.
  • Cold Bend Test, Section 23.
  • Durability of Ink-Print Test, Section 27
  • Crush Resistance Test, Section 28.
  • Dielectric Test, Method I, Section 29.
  • Dielectric Test, Method II, Section 30.
  • Dielectric Test, Method III, Section 31.
  • Horizontal Flame Test for Internal Wiring, Section 40.

20160719

  • 試作7/0.20TA(導体OD約0.6)
  • 添加比例6356:52FR:色母=10:1:0.4
  • 乾燥110℃x4小時以上
  • 水平燃燒試驗:https://youtu.be/_J5qD_PreOs
    • 試樣1(黑):
      • 厚度0.15
      • 表面粗糙(魚鱗狀),伸長率OK
      • 耐燃Fail(超過10cm)
    • 試樣2(白):
      • 厚度0.15
      • 表面粗糙(魚鱗狀),伸長率OK
      • 耐燃Fail(超過10cm)
    • 試樣3(白)
      • 厚度0.3
      • 表面OK,伸長率OK
      • 耐燃Fail(超過10cm,且13秒時滴落引燃棉花)

20160713含水率

  • 52FR 製程要求含水率(Processing moisture content≦0.08%)
  • 6356 SPC: Water Absorption(Immersion 24hr) 0.3%,(Processing moisture content≦0.1%)
  • 實測 110℃X4hr
    • 52FR 去除含水率 0.23%
    • 6356 去除含水率 0.26%

2016/05/27試作

  • 改以6356+ FR試作
    • 10:1:0.4
    • 添加色母表面粗糙,沒有伸長率
    • 不添加色母表面略改善,伸長率仍不佳。

2016/05/18承茂供料52FR 3kg

  • 以 STYLE 10912及10140進行試作設計
    • 10912 1/0.81AC 0.22t 1.25ψ
    • 10140 1/0.81AC 0.15t 1.1ψ
    • 採用Hytrel 5556:52FR 10:1

2016/05/12承茂提問

  • 尼龍部份:
    • PA6 與PA66差異?
      • 差異不大,杜邦主要生產PA66。
    • 押出級及射出級除流動性差異外?還有哪些?目前TSK使用的是射出級的。
      • 射出級分子量較小,所以流動性比較好,押出級有再脫水增加黏著性,剛性的部份差不多。
    • 目前遇到的問題是SR-PVC(0.15t/0.9d)+Nylon(0.1t/1.1d),在彎折時會尼龍會剝離,在識別印時時,壓力也會造成尼龍剝離。
      • 會再提供PA66的品號及價格。
  • Hytrel:
    • 目前是否有用於絕緣的牌號阻燃效果比較好,最小厚度要求多少
      • 5556HR,UL 有來文,有通過10912,杜邦會再提供該文件。因添加熱穩定劑,本色偏黃。
    • 計劃申請UL AWM STYLE 10912(Horizontal flame)
    • 添加阻燃劑的效果如何(52FR V-2?)?
      • 會提供52FR 3Kg,提供試料,若還有試樣要求,可提供50KG FREE SAMPLE
      • chrome_2016-05-12_11-31-51.png (Hytrel Design Guide.pdf)
    • 電纜一般是否都用套管式作業(tubing),厚度最厚能到多少(TSK tubing+Vacuum)?
      • tubing 2-3mm ok

其他供應商