「裁線條碼亮燈」:修訂間差異
| (未顯示同一使用者於中間所作的 3 次修訂) | |||
| 第1行: | 第1行: | ||
==20200604看板== | |||
<c> | |||
//接收及LED看板 | |||
//20200604以pi send to Arduino uno | |||
//20190221增加經過10分鐘看板未輸入條碼,LED看板全黑 | |||
#include <SPI.h> | |||
#include <RF24.h> | |||
#include <Adafruit_GFX.h> // Core graphics library | |||
#include <RGBmatrixPanel.h> // Hardware-specific library | |||
#define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega) | |||
#define LAT A3 | |||
#define OE 9 | |||
#define A A0 | |||
#define B A1 | |||
#define C A2 | |||
RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false); | |||
RF24 rf24(A4, A5); // CE腳, CSN腳 | |||
const uint64_t addr = 0xF0F0F0F0E2LL; | |||
const uint64_t pipe = 0xE8E8F0F0E2LL; | |||
void setup() { | |||
Serial.begin(9600); | |||
rf24.begin(); | |||
matrix.begin(); | |||
rf24.setChannel(0x72); // 設定頻道編號 | |||
rf24.setPALevel(RF24_PA_MAX); | |||
rf24.setDataRate(RF24_1MBPS); | |||
rf24.openReadingPipe(1, pipe); // 開啟通道和位址 | |||
rf24.enableDynamicPayloads(); | |||
rf24.powerUp(); | |||
rf24.startListening(); // 開始監聽無線廣播 | |||
matrix.fillScreen(matrix.Color333(0, 0, 0)); | |||
matrix.setTextColor(matrix.Color333(7,0,0)); | |||
matrix.setCursor(8, 4); | |||
matrix.print("TSK"); | |||
} | |||
unsigned long starttime; | |||
unsigned long runtime; | |||
void loop() { | |||
starttime = millis()/60000; | |||
if (rf24.available()) { | |||
char msg[32] = ""; | |||
//char s[10]; | |||
runtime = millis()/60000; | |||
rf24.read(&msg, sizeof(msg)); | |||
String myString = String(msg); | |||
int sX=(myString.length() >=5)? 1:5 ; | |||
matrix.setCursor(sX, 1); | |||
matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black' | |||
//線長大於等於10紅色,小於10橙色 | |||
if(atof(msg)<3){ | |||
matrix.setTextColor(matrix.Color333(0,7,3)); | |||
}else if(atof(msg)>=3 && atof(msg)<10){ | |||
matrix.setTextColor(matrix.Color333(7,3,0)); | |||
}else{ | |||
matrix.setTextColor(matrix.Color333(7,0,0)); | |||
} | |||
delay(30); | |||
matrix.setTextSize(1); | |||
matrix.print(myString); | |||
matrix.setCursor(25, 8); | |||
matrix.setTextColor(matrix.Color333(0,7,0)); | |||
matrix.print("m"); | |||
Serial.println(myString); | |||
} | |||
//超過10分鐘沒有輸入條碼,則關閉LED看板 | |||
if((starttime-runtime)>=10){ | |||
matrix.fillScreen(matrix.Color333(0, 0, 0)); | |||
} | |||
//Serial.println(starttime-runtime); | |||
delay(300); | |||
} | |||
</c> | |||
==20190320看板*2== | |||
<c> | |||
//接收及LED看板 | |||
//20190221增加經過10分鐘看板未輸入條碼,LED看板全黑 | |||
#include <SPI.h> | |||
#include "RF24.h" | |||
#include <Adafruit_GFX.h> // Core graphics library | |||
#include <RGBmatrixPanel.h> // Hardware-specific library | |||
#define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega) | |||
#define LAT A3 | |||
#define OE 9 | |||
#define A A0 | |||
#define B A1 | |||
#define C A2f | |||
#define n 2 // inline panels number | |||
RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false,32*n); | |||
RF24 rf24(A4, A5); // CE腳, CSN腳 | |||
const byte addr[] = "1Node"; | |||
const byte pipe = 1; // 指定通道編號 | |||
void setup() { | |||
Serial.begin(9600); | |||
rf24.begin(); | |||
matrix.begin(); | |||
rf24.setChannel(76); // 設定頻道編號 | |||
rf24.setPALevel(RF24_PA_MAX); | |||
rf24.setDataRate(RF24_250KBPS); | |||
rf24.openReadingPipe(pipe, addr); // 開啟通道和位址 | |||
rf24.startListening(); // 開始監聽無線廣播 | |||
matrix.fillScreen(matrix.Color333(0, 0, 0)); | |||
matrix.setTextColor(matrix.Color333(7,0,0)); | |||
matrix.setCursor(8, 4); | |||
matrix.print("TSK"); | |||
} | |||
unsigned long starttime; | |||
unsigned long runtime; | |||
void loop() { | |||
starttime = millis()/60000; | |||
if (rf24.available(&pipe)) { | |||
char msg[32] = ""; | |||
//char s[10]; | |||
runtime = millis()/60000; | |||
rf24.read(&msg, sizeof(msg)); | |||
String myString = String(msg); | |||
int sX=(myString.length() >=5)? 1:5 ; | |||
matrix.setCursor(sX, 1); | |||
matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black' | |||
//線長大於等於10紅色,小於10橙色 | |||
if(atof(msg)<3){ | |||
matrix.setTextColor(matrix.Color333(0,7,3)); | |||
}else if(atof(msg)>=3 && atof(msg)<10){ | |||
matrix.setTextColor(matrix.Color333(7,3,0)); | |||
}else{ | |||
matrix.setTextColor(matrix.Color333(7,0,0)); | |||
} | |||
delay(30); | |||
matrix.setTextSize(2); | |||
matrix.print(myString); | |||
matrix.setCursor(25, 8); | |||
matrix.setTextColor(matrix.Color333(0,7,0)); | |||
matrix.print("m"); | |||
Serial.println(myString); | |||
} | |||
//超過10分鐘沒有輸入條碼,則關閉LED看板 | |||
if((starttime-runtime)>=10){ | |||
matrix.fillScreen(matrix.Color333(0, 0, 0)); | |||
} | |||
//Serial.println(starttime-runtime); | |||
delay(300); | |||
} | |||
</c> | |||
==20190222看板== | ==20190222看板== | ||
| 第77行: | 第237行: | ||
} | } | ||
</c> | </c> | ||
==20190223== | ==20190223== | ||
<c> | <c> | ||
| 第1,184行: | 第1,345行: | ||
*保護盒 90+130=220元 | *保護盒 90+130=220元 | ||
*杜邦連接糸線 60元 | *杜邦連接糸線 60元 | ||
*總計1400元 | |||
==工程需求== | ==工程需求== | ||
| 第1,197行: | 第1,359行: | ||
**LED看板固定 | **LED看板固定 | ||
**看板控制器固定 | **看板控制器固定 | ||
**看板電源供應器固定 | **看板電源供應器固定 | ||
**[https://learn.adafruit.com/32x16-32x32-rgb-led-matrix/connecting-with-jumper-wires 看板接線方法] | |||
*電源插座及開關(或插拔插頭) | *電源插座及開關(或插拔插頭) | ||
**桌面電源 : 一桌至少三孔插座 | **桌面電源 : 一桌至少三孔插座 | ||
**看板電源 : 一桌至少三孔插座 | **看板電源 : 一桌至少三孔插座 | ||
於 2020年6月4日 (四) 15:38 的最新修訂
20200604看板
<c> //接收及LED看板 //20200604以pi send to Arduino uno //20190221增加經過10分鐘看板未輸入條碼,LED看板全黑
- include <SPI.h>
- include <RF24.h>
- include <Adafruit_GFX.h> // Core graphics library
- include <RGBmatrixPanel.h> // Hardware-specific library
- define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega)
- define LAT A3
- define OE 9
- define A A0
- define B A1
- define C A2
RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false); RF24 rf24(A4, A5); // CE腳, CSN腳 const uint64_t addr = 0xF0F0F0F0E2LL; const uint64_t pipe = 0xE8E8F0F0E2LL;
void setup() {
Serial.begin(9600);
rf24.begin();
matrix.begin();
rf24.setChannel(0x72); // 設定頻道編號
rf24.setPALevel(RF24_PA_MAX);
rf24.setDataRate(RF24_1MBPS);
rf24.openReadingPipe(1, pipe); // 開啟通道和位址
rf24.enableDynamicPayloads();
rf24.powerUp();
rf24.startListening(); // 開始監聽無線廣播
matrix.fillScreen(matrix.Color333(0, 0, 0));
matrix.setTextColor(matrix.Color333(7,0,0));
matrix.setCursor(8, 4);
matrix.print("TSK");
}
unsigned long starttime; unsigned long runtime;
void loop() {
starttime = millis()/60000;
if (rf24.available()) {
char msg[32] = "";
//char s[10];
runtime = millis()/60000;
rf24.read(&msg, sizeof(msg));
String myString = String(msg);
int sX=(myString.length() >=5)? 1:5 ;
matrix.setCursor(sX, 1);
matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black'
//線長大於等於10紅色,小於10橙色
if(atof(msg)<3){
matrix.setTextColor(matrix.Color333(0,7,3));
}else if(atof(msg)>=3 && atof(msg)<10){
matrix.setTextColor(matrix.Color333(7,3,0));
}else{
matrix.setTextColor(matrix.Color333(7,0,0));
}
delay(30);
matrix.setTextSize(1);
matrix.print(myString);
matrix.setCursor(25, 8);
matrix.setTextColor(matrix.Color333(0,7,0));
matrix.print("m");
Serial.println(myString);
}
//超過10分鐘沒有輸入條碼,則關閉LED看板
if((starttime-runtime)>=10){
matrix.fillScreen(matrix.Color333(0, 0, 0));
}
//Serial.println(starttime-runtime);
delay(300);
} </c>
20190320看板*2
<c> //接收及LED看板 //20190221增加經過10分鐘看板未輸入條碼,LED看板全黑
- include <SPI.h>
- include "RF24.h"
- include <Adafruit_GFX.h> // Core graphics library
- include <RGBmatrixPanel.h> // Hardware-specific library
- define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega)
- define LAT A3
- define OE 9
- define A A0
- define B A1
- define C A2f
- define n 2 // inline panels number
RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false,32*n); RF24 rf24(A4, A5); // CE腳, CSN腳 const byte addr[] = "1Node"; const byte pipe = 1; // 指定通道編號
void setup() {
Serial.begin(9600);
rf24.begin();
matrix.begin();
rf24.setChannel(76); // 設定頻道編號
rf24.setPALevel(RF24_PA_MAX);
rf24.setDataRate(RF24_250KBPS);
rf24.openReadingPipe(pipe, addr); // 開啟通道和位址
rf24.startListening(); // 開始監聽無線廣播
matrix.fillScreen(matrix.Color333(0, 0, 0));
matrix.setTextColor(matrix.Color333(7,0,0));
matrix.setCursor(8, 4);
matrix.print("TSK");
}
unsigned long starttime; unsigned long runtime;
void loop() {
starttime = millis()/60000;
if (rf24.available(&pipe)) {
char msg[32] = "";
//char s[10];
runtime = millis()/60000;
rf24.read(&msg, sizeof(msg));
String myString = String(msg);
int sX=(myString.length() >=5)? 1:5 ;
matrix.setCursor(sX, 1);
matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black'
//線長大於等於10紅色,小於10橙色
if(atof(msg)<3){
matrix.setTextColor(matrix.Color333(0,7,3));
}else if(atof(msg)>=3 && atof(msg)<10){
matrix.setTextColor(matrix.Color333(7,3,0));
}else{
matrix.setTextColor(matrix.Color333(7,0,0));
}
delay(30);
matrix.setTextSize(2);
matrix.print(myString);
matrix.setCursor(25, 8);
matrix.setTextColor(matrix.Color333(0,7,0));
matrix.print("m");
Serial.println(myString);
}
//超過10分鐘沒有輸入條碼,則關閉LED看板
if((starttime-runtime)>=10){
matrix.fillScreen(matrix.Color333(0, 0, 0));
}
//Serial.println(starttime-runtime);
delay(300);
}
</c>
20190222看板
<c> //接收及LED看板 //20190221增加經過10分鐘看板未輸入條碼,LED看板全黑
- include <SPI.h>
- include "RF24.h"
- include <Adafruit_GFX.h> // Core graphics library
- include <RGBmatrixPanel.h> // Hardware-specific library
- define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega)
- define LAT A3
- define OE 9
- define A A0
- define B A1
- define C A2
RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false); RF24 rf24(A4, A5); // CE腳, CSN腳 const byte addr[] = "1Node"; const byte pipe = 1; // 指定通道編號
void setup() {
Serial.begin(9600);
rf24.begin();
matrix.begin();
rf24.setChannel(76); // 設定頻道編號
rf24.setPALevel(RF24_PA_MAX);
rf24.setDataRate(RF24_250KBPS);
rf24.openReadingPipe(pipe, addr); // 開啟通道和位址
rf24.startListening(); // 開始監聽無線廣播
matrix.fillScreen(matrix.Color333(0, 0, 0));
matrix.setTextColor(matrix.Color333(7,0,0));
matrix.setCursor(8, 4);
matrix.print("TSK");
}
unsigned long starttime; unsigned long runtime;
void loop() {
starttime = millis()/60000;
if (rf24.available(&pipe)) {
char msg[32] = "";
//char s[10];
runtime = millis()/60000;
rf24.read(&msg, sizeof(msg));
String myString = String(msg);
int sX=(myString.length() >=5)? 1:5 ;
matrix.setCursor(sX, 1);
matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black'
//線長大於等於10紅色,小於10橙色
if(atof(msg)<3){
matrix.setTextColor(matrix.Color333(0,7,3));
}else if(atof(msg)>=3 && atof(msg)<10){
matrix.setTextColor(matrix.Color333(7,3,0));
}else{
matrix.setTextColor(matrix.Color333(7,0,0));
}
delay(30);
matrix.setTextSize(1);
matrix.print(myString);
matrix.setCursor(25, 8);
matrix.setTextColor(matrix.Color333(0,7,0));
matrix.print("m");
Serial.println(myString);
}
//超過10分鐘沒有輸入條碼,則關閉LED看板
if((starttime-runtime)>=10){
matrix.fillScreen(matrix.Color333(0, 0, 0));
}
//Serial.println(starttime-runtime);
delay(300);
} </c>
20190223
<c> //發送,LED燈條及條碼掃瞄 //20190220增加LED燈條後移長度 //20190222修改燈條後移長度0.3m //修改loop判斷條件的延時時間
- include <SPI.h>
- include "RF24.h"
- include <printf.h>
- include <usbhid.h>
- include <usbhub.h>
- include <hiduniversal.h>
- include <hidboot.h>
- include <FastLED.h>
- define NUM_LEDS 1200 // led灯数量20m*60顆
- define DATA_PIN A5 // 数据传输引脚(Digital 6)
- define BRIGHTNESS 20 //設定led亮度
- define FRONT_LENGTH 0.295 //LED燈條後移長度
unsigned long starttime; unsigned long runtime; int ck_delay; RF24 rf24(A0, A1); // CE腳, CSN腳 const byte addr[] = "1Node";
String s;
CRGB leds[NUM_LEDS];
class MyParser : public HIDReportParser {
public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished();
};
MyParser::MyParser() {}
void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) {
// If error or empty, return
if (buf[2] == 1 || buf[2] == 0) return;
for (uint8_t i = 7; i >= 2; i--) {
// If empty, skip
if (buf[i] == 0) continue;
// If enter signal emitted, scan finished
if (buf[i] == UHS_HID_BOOT_KEY_ENTER) {
OnScanFinished();
}
// If not, continue normally
else {
// If bit position not in 2, it's uppercase words
OnKeyScanned(i > 2, buf, buf[i]);
}
return;
}
}
uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) {
// Letters
if (VALUE_WITHIN(key, 0x04, 0x1d)) {
if (upper) return (key - 4 + 'A');
else return (key - 4 + 'a');
}
// Numbers
else if (VALUE_WITHIN(key, 0x1e, 0x27)) {
return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1');
}
if(key== 55 ) {
return 46;
}else return 0;
}
void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) {
uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(50); s=(ascii==0)? s : s+ (char)ascii ; ck_delay=0;
}
void MyParser::OnScanFinished() {
//int i,k,j=2;
float a=s.toFloat();
char msg[32];
ck_delay=1;
s.toCharArray(msg,32);
a=(a-FRONT_LENGTH)*60;
int uplimit=ceil(a);
int downlimit=floor(a);
delay(150);
rf24.write(&msg, sizeof(msg)); // 傳送資料
runtime = millis()/60000;
FastLED.clear();
delay(30);
if(uplimit==downlimit){
leds[uplimit] = CRGB::White;
}else{
leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red
leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red
}
FastLED.show();
s="";
}
USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser;
void setup() {
FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯
FastLED.setBrightness( BRIGHTNESS );
Serial.begin( 9600 );
// Serial.println("Start");
printf_begin();
rf24.begin();
rf24.setChannel(76); // 設定頻道編號
rf24.openWritingPipe(addr); // 設定通道位址
rf24.setPALevel(RF24_PA_MAX); // 設定廣播功率
rf24.setDataRate(RF24_250KBPS); // 設定傳輸速率
rf24.stopListening(); // 停止偵聽;設定成發射模式
//rf24.printDetails();
if (Usb.Init() == -1) {
Serial.println("OSC did not start.");
}
delay( 50 );
Hid.SetReportParser(0, &Parser);
FastLED.clear();
FastLED.show();
}
void loop() {
starttime = millis()/60000;
Usb.Task();
//十五分鐘入輸入條碼,關閉led燈條
if((starttime-runtime)>=15){
FastLED.clear();
FastLED.show();
}
if(ck_delay==1)delay(200);
}
</c>
20190221
<c> //接收及LED看板 //20190221增加經過10分鐘看板未輸入條碼,LED看板全黑
- include <SPI.h>
- include "RF24.h"
- include <Adafruit_GFX.h> // Core graphics library
- include <RGBmatrixPanel.h> // Hardware-specific library
- define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega)
- define LAT A3
- define OE 9
- define A A0
- define B A1
- define C A2
RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false); RF24 rf24(A4, A5); // CE腳, CSN腳 const byte addr[] = "1Node"; const byte pipe = 1; // 指定通道編號
void setup() {
Serial.begin(9600);
rf24.begin();
matrix.begin();
rf24.setChannel(76); // 設定頻道編號
rf24.setPALevel(RF24_PA_MAX);
rf24.setDataRate(RF24_250KBPS);
rf24.openReadingPipe(pipe, addr); // 開啟通道和位址
rf24.startListening(); // 開始監聽無線廣播
matrix.fillScreen(matrix.Color333(0, 0, 0));
matrix.setTextColor(matrix.Color333(7,4,0));
matrix.setCursor(8, 4);
matrix.print("TSK");
}
unsigned long starttime; unsigned long runtime;
void loop() {
starttime = millis()/60000;
if (rf24.available(&pipe)) {
char msg[32] = "";
//char s[10];
runtime = millis()/60000;
rf24.read(&msg, sizeof(msg));
String myString = String(msg);
int sX=(myString.length() >=5)? 1:5 ;
matrix.setCursor(sX, 1);
matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black'
//線長大於等於10紅色,小於10橙色
if(atof(msg)<3){
matrix.setTextColor(matrix.Color333(0,7,7));
}else if(atof(msg)>=3 && atof(msg)<10){
matrix.setTextColor(matrix.Color333(7,3,0));
}else{
matrix.setTextColor(matrix.Color333(7,0,0));
}
delay(30);
matrix.setTextSize(1);
matrix.print(myString);
matrix.setCursor(25, 8);
matrix.setTextColor(matrix.Color333(0,7,0));
matrix.print("m");
Serial.println(myString);
}
//超過10分鐘沒有輸入條碼,則關閉LED看板
if((starttime-runtime)>=10){
matrix.fillScreen(matrix.Color333(0, 0, 0));
}
//Serial.println(starttime-runtime);
delay(300);
}
</c> <c> //發送,LED燈條及條碼掃瞄 //20190220增加LED燈條後移長度
- include <SPI.h>
- include "RF24.h"
- include <printf.h>
- include <usbhid.h>
- include <usbhub.h>
- include <hiduniversal.h>
- include <hidboot.h>
- include <FastLED.h>
- define NUM_LEDS 1200 // led灯数量20m*60顆
- define DATA_PIN A5 // 数据传输引脚(Digital 6)
- define BRIGHTNESS 18 //設定led亮度
- define FRONT_LENGTH 0.3 //LED燈條後移長度
unsigned long starttime; unsigned long runtime;
RF24 rf24(A0, A1); // CE腳, CSN腳 const byte addr[] = "1Node";
String s;
CRGB leds[NUM_LEDS];
class MyParser : public HIDReportParser {
public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished();
};
MyParser::MyParser() {}
void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) {
// If error or empty, return
if (buf[2] == 1 || buf[2] == 0) return;
for (uint8_t i = 7; i >= 2; i--) {
// If empty, skip
if (buf[i] == 0) continue;
// If enter signal emitted, scan finished
if (buf[i] == UHS_HID_BOOT_KEY_ENTER) {
OnScanFinished();
}
// If not, continue normally
else {
// If bit position not in 2, it's uppercase words
OnKeyScanned(i > 2, buf, buf[i]);
}
return;
}
}
uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) {
// Letters
if (VALUE_WITHIN(key, 0x04, 0x1d)) {
if (upper) return (key - 4 + 'A');
else return (key - 4 + 'a');
}
// Numbers
else if (VALUE_WITHIN(key, 0x1e, 0x27)) {
return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1');
}
if(key== 55 ) {
return 46;
}else return 0;
}
void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) {
uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(50); s=(ascii==0)? s : s+ (char)ascii ;
}
void MyParser::OnScanFinished() {
int i,k,j=2;
float a=s.toFloat();
char msg[32];
s.toCharArray(msg,32);
a=(a-FRONT_LENGTH)*60;
int uplimit=ceil(a)-1;
int downlimit=floor(a)-1;
delay(150);
rf24.write(&msg, sizeof(msg)); // 傳送資料
runtime = millis()/60000;
Serial.println(s);
FastLED.clear();
delay(30);
if(uplimit==downlimit){
leds[uplimit] = CRGB::White;
}else{
leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red
leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red
}
FastLED.show();
s="";
}
USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser;
void setup() {
FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯
FastLED.setBrightness( BRIGHTNESS );
Serial.begin( 9600 );
// Serial.println("Start");
printf_begin();
rf24.begin();
rf24.setChannel(76); // 設定頻道編號
rf24.openWritingPipe(addr); // 設定通道位址
rf24.setPALevel(RF24_PA_MAX); // 設定廣播功率
rf24.setDataRate(RF24_250KBPS); // 設定傳輸速率
rf24.stopListening(); // 停止偵聽;設定成發射模式
rf24.printDetails();
if (Usb.Init() == -1) {
Serial.println("OSC did not start.");
}
delay( 50 );
Hid.SetReportParser(0, &Parser);
}
void loop() {
starttime = millis()/60000;
Usb.Task();
//十五分鐘入輸入條碼,關閉led燈條
if((starttime-runtime)>=15){
FastLED.clear();
FastLED.show();
}
delay(2);
} </c>
20190117
<c> //20190124 修正桌上型掃瞄器C39 barcod前後置0的轉碼誤判 //s=(ascii==0)? s : s+ (char)ascii ; //20190117 改用Arduino Mega2560
- include <usbhid.h>
- include <usbhub.h>
- include <hiduniversal.h>
- include <hidboot.h>
- include <SPI.h>
- include <FastLED.h>
- include <Adafruit_GFX.h> // Core graphics library
- include <RGBmatrixPanel.h> // Hardware-specific library
- define NUM_LEDS 1200 // led灯数量20m*60顆
- define DATA_PIN A5 // 数据传输引脚(Digital 6)
- define BRIGHTNESS 20 //設定led亮度
- define CLK 11 // MUST be on PORTB! (Use pin 11 on Mega)
- define LAT A4
- define OE 9
- define A A0
- define B A1
- define C A2
//int LIGHTDELAY= 1/NUM_LEDS; String s; CRGB leds[NUM_LEDS]; RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false);
class MyParser : public HIDReportParser {
public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished();
};
MyParser::MyParser() {}
void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) {
// If error or empty, return
if (buf[2] == 1 || buf[2] == 0) return;
for (uint8_t i = 7; i >= 2; i--) {
// If empty, skip
if (buf[i] == 0) continue;
// If enter signal emitted, scan finished
if (buf[i] == UHS_HID_BOOT_KEY_ENTER) {
OnScanFinished();
}
// If not, continue normally
else {
// If bit position not in 2, it's uppercase words
OnKeyScanned(i > 2, buf, buf[i]);
}
return;
}
}
uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) {
// Letters
if (VALUE_WITHIN(key, 0x04, 0x1d)) {
if (upper) return (key - 4 + 'A');
else return (key - 4 + 'a');
}
// Numbers
else if (VALUE_WITHIN(key, 0x1e, 0x27)) {
return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1');
}
if(key== 55 ) {
return 46;
}else return 0;
}
void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) {
uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(50); s=(ascii==0)? s : s+ (char)ascii ;
}
void MyParser::OnScanFinished() {
int i,k,j=2; float a=s.toFloat(); a=a*60; int uplimit=ceil(a)-1; int downlimit=floor(a)-1; int sX=(s.length()>=5)? 1:5 ; matrix.setCursor(sX, 1); matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black' matrix.setTextColor(matrix.Color333(7,0,0)); delay(30); matrix.setTextSize(1); Serial.println(s); matrix.print(s); FastLED.clear();
/*
int delaynum= ceil(downlimit/60.0)*3;
//Serial.println(delaynum);
for(i=0;i< downlimit;i+=delaynum){
leds[i] = CRGB::Yellow;
FastLED.show();
// delay(1);
leds[i] = CRGB::Black;
FastLED.show();
}
- /
delay(30);
if(uplimit==downlimit){
leds[uplimit] = CRGB::White;
}else{
leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red
leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red
}
FastLED.show();
matrix.setCursor(25, 8);
matrix.setTextColor(matrix.Color333(0,7,0));
matrix.print("m");
s="";
}
USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser;
void setup() {
FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯
FastLED.setBrightness( BRIGHTNESS );
matrix.begin();
Serial.begin( 115200 );
Serial.println("Start");
if (Usb.Init() == -1) {
Serial.println("OSC did not start.");
}
delay( 100 );
Hid.SetReportParser(0, &Parser);
matrix.fillScreen(matrix.Color333(0, 0, 0));
}
void loop() {
Usb.Task();
}
</c>
20190115
<c> //20190115 增加LED看板顯示
- include <usbhid.h>
- include <usbhub.h>
- include <hiduniversal.h>
- include <hidboot.h>
- include <SPI.h>
- include <FastLED.h>
- include <Adafruit_GFX.h> // Core graphics library
- include <RGBmatrixPanel.h> // Hardware-specific library
- define NUM_LEDS 60 // led灯数量20m*60顆
- define DATA_PIN A5 // 数据传输引脚(Digital 6)
- define BRIGHTNESS 25 //設定led亮度
- define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega)
- define LAT A3
- define OE 9
- define A A0
- define B A1
- define C A2
//int LIGHTDELAY= 1/NUM_LEDS; String s; CRGB leds[NUM_LEDS]; RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false);
class MyParser : public HIDReportParser {
public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished();
};
MyParser::MyParser() {}
void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) {
// If error or empty, return
if (buf[2] == 1 || buf[2] == 0) return;
for (uint8_t i = 7; i >= 2; i--) {
// If empty, skip
if (buf[i] == 0) continue;
// If enter signal emitted, scan finished
if (buf[i] == UHS_HID_BOOT_KEY_ENTER) {
OnScanFinished();
}
// If not, continue normally
else {
// If bit position not in 2, it's uppercase words
OnKeyScanned(i > 2, buf, buf[i]);
}
return;
}
}
uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) {
// Letters
if (VALUE_WITHIN(key, 0x04, 0x1d)) {
if (upper) return (key - 4 + 'A');
else return (key - 4 + 'a');
}
// Numbers
else if (VALUE_WITHIN(key, 0x1e, 0x27)) {
return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1');
}
if(key== 55 ) {
return 46;
}else return 0;
}
void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) {
uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(100); s= s + ((char)ascii) + "";
}
void MyParser::OnScanFinished() {
int i,k,j=2; float a=s.toFloat(); a=a*60; int uplimit=ceil(a)-1; int downlimit=floor(a)-1; matrix.setCursor(5, 0); matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black' matrix.setTextColor(matrix.Color333(7,0,0)); delay(30); matrix.setTextSize(1); matrix.print(s); FastLED.clear();
/*
int delaynum= ceil(downlimit/60.0);
for(i=1;i< downlimit;i+=delaynum){
leds[i] = CRGB::Yellow;
FastLED.show();
delay(10);
FastLED.clear();
}
*/
delay(30);
if(uplimit==downlimit){
leds[uplimit] = CRGB::White;
}else{
leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red
leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red
}
FastLED.show();
matrix.setCursor(25, 7);
matrix.setTextColor(matrix.Color333(0,7,0));
matrix.print("m");
s="";
}
USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser;
void setup() {
FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯
FastLED.setBrightness( BRIGHTNESS );
matrix.begin();
Serial.begin( 115200 );
Serial.println("Start");
if (Usb.Init() == -1) {
Serial.println("OSC did not start.");
}
delay( 100 );
Hid.SetReportParser(0, &Parser);
matrix.fillScreen(matrix.Color333(0, 0, 0));
}
void loop() {
Usb.Task();
}
</c>
20190104-2
<c> //20190104增加LCD顯示
- include <Wire.h>
- include <LiquidCrystal_I2C.h>
- include <usbhid.h>
- include <usbhub.h>
- include <hiduniversal.h>
- include <hidboot.h>
- include <SPI.h>
- include <FastLED.h>
- define NUM_LEDS 60 // led灯数量
- define DATA_PIN 6 // 数据传输引脚(Digital 6)
- define BRIGHTNESS 25 //設定led亮度
int LIGHTDELAY= 60/NUM_LEDS/60; String s; CRGB leds[NUM_LEDS]; LiquidCrystal_I2C lcd(0x27,20,4); // set the LCD address to 0x27 for a 16 chars and 2 line display
class MyParser : public HIDReportParser {
public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished();
};
MyParser::MyParser() {}
void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) {
// If error or empty, return
if (buf[2] == 1 || buf[2] == 0) return;
for (uint8_t i = 7; i >= 2; i--) {
// If empty, skip
if (buf[i] == 0) continue;
// If enter signal emitted, scan finished
if (buf[i] == UHS_HID_BOOT_KEY_ENTER) {
OnScanFinished();
}
// If not, continue normally
else {
// If bit position not in 2, it's uppercase words
OnKeyScanned(i > 2, buf, buf[i]);
}
return;
}
}
uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) {
// Letters
if (VALUE_WITHIN(key, 0x04, 0x1d)) {
if (upper) return (key - 4 + 'A');
else return (key - 4 + 'a');
}
// Numbers
else if (VALUE_WITHIN(key, 0x1e, 0x27)) {
return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1');
}
if(key== 55 ) {
return 46;
}else return 0;
}
void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) {
uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(100); s= s + ((char)ascii) + "";
}
void MyParser::OnScanFinished() {
int i,k,j=2;
float a=s.toFloat();
String lcdtext2=s +" m";
lcd.clear();
lcd.setCursor(1,0);
lcd.print("Cable Length:");
lcd.setCursor(6,1);
lcd.print(lcdtext2);
a=a*60;
int uplimit=ceil(a)-1;
int downlimit=floor(a)-1;
FastLED.clear();
for(i=1;i< downlimit;i++){
leds[i] = CRGB::Yellow;
FastLED.show();
delay(LIGHTDELAY);
FastLED.clear();
}
if(uplimit==downlimit){
leds[uplimit] = CRGB::White;
}else{
leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red
leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red
}
FastLED.show();
s="";
}
USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser;
void setup() {
FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯
FastLED.setBrightness( BRIGHTNESS );
Serial.begin( 115200 );
lcd.init();
lcd.backlight();
lcd.setCursor(1,0);
lcd.print("Cable Length:");
if (Usb.Init() == -1) {
Serial.println("OSC did not start.");
}
delay( 200 );
Hid.SetReportParser(0, &Parser);
}
void loop() {
Usb.Task();
}
</c>
20190104-1
<c> //20190104增加流水燈
- include <usbhid.h>
- include <usbhub.h>
- include <hiduniversal.h>
- include <hidboot.h>
- include <SPI.h>
- include <FastLED.h>
- define NUM_LEDS 60 // led灯数量
- define DATA_PIN 6 // 数据传输引脚(Digital 6)
- define BRIGHTNESS 25 //設定led亮度
int LIGHTDELAY= 60/NUM_LEDS/60; String s; CRGB leds[NUM_LEDS];
class MyParser : public HIDReportParser {
public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished();
};
MyParser::MyParser() {}
void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) {
// If error or empty, return
if (buf[2] == 1 || buf[2] == 0) return;
for (uint8_t i = 7; i >= 2; i--) {
// If empty, skip
if (buf[i] == 0) continue;
// If enter signal emitted, scan finished
if (buf[i] == UHS_HID_BOOT_KEY_ENTER) {
OnScanFinished();
}
// If not, continue normally
else {
// If bit position not in 2, it's uppercase words
OnKeyScanned(i > 2, buf, buf[i]);
}
return;
}
}
uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) {
// Letters
if (VALUE_WITHIN(key, 0x04, 0x1d)) {
if (upper) return (key - 4 + 'A');
else return (key - 4 + 'a');
}
// Numbers
else if (VALUE_WITHIN(key, 0x1e, 0x27)) {
return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1');
}
if(key== 55 ) {
return 46;
}else return 0;
}
void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) {
uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(100); s= s + ((char)ascii) + "";
}
void MyParser::OnScanFinished() {
int i,k,j=2;
float a=s.toFloat();
a=a*60;
int uplimit=ceil(a)-1;
int downlimit=floor(a)-1;
//Serial.println(uplimit);
FastLED.clear();
for(i=1;i< downlimit;i++){
leds[i] = CRGB::Yellow;
FastLED.show();
delay(LIGHTDELAY);
FastLED.clear();
}
if(uplimit==downlimit){
leds[uplimit] = CRGB::White;
}else{
leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red
leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red
}
FastLED.show();
s="";
}
USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser;
void setup() {
FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯
FastLED.setBrightness( BRIGHTNESS );
Serial.begin( 115200 );
Serial.println("Start");
if (Usb.Init() == -1) {
Serial.println("OSC did not start.");
}
delay( 200 );
Hid.SetReportParser(0, &Parser);
}
void loop() {
Usb.Task();
}
</c>
20190103
<c>
- include <usbhid.h>
- include <usbhub.h>
- include <hiduniversal.h>
- include <hidboot.h>
- include <SPI.h>
- include <FastLED.h>
- define NUM_LEDS 60 // led灯数量
- define DATA_PIN 6 // 数据传输引脚(Digital 6)
- define BRIGHTNESS 25 ////設定led亮度
String s; CRGB leds[NUM_LEDS];
class MyParser : public HIDReportParser {
public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished();
};
MyParser::MyParser() {}
void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) {
// If error or empty, return if (buf[2] == 1 || buf[2] == 0) return;
for (uint8_t i = 7; i >= 2; i--) {
// If empty, skip
if (buf[i] == 0) continue;
// If enter signal emitted, scan finished
if (buf[i] == UHS_HID_BOOT_KEY_ENTER) {
OnScanFinished();
}
// If not, continue normally
else {
// If bit position not in 2, it's uppercase words
OnKeyScanned(i > 2, buf, buf[i]);
}
return; }
}
uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) {
// Letters
if (VALUE_WITHIN(key, 0x04, 0x1d)) {
if (upper) return (key - 4 + 'A');
else return (key - 4 + 'a');
}
// Numbers
else if (VALUE_WITHIN(key, 0x1e, 0x27)) {
return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1');
}
if(key== 55 ) {
return 46;
}else return 0;
}
void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) {
uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(100); s= s + ((char)ascii) + "";
//s=s + ascii; }
void MyParser::OnScanFinished() {
float a=s.toFloat();
a=a*60;
int uplimit=ceil(a)-1;
int downlimit=floor(a)-1;
Serial.println(uplimit);
FastLED.clear();
if(uplimit==downlimit){
leds[uplimit] = CRGB::White;
}else{
leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red
leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red
}
FastLED.show();
s="";
}
USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser;
void setup() {
FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯
FastLED.setBrightness( BRIGHTNESS );
Serial.begin( 115200 );
Serial.println("Start");
if (Usb.Init() == -1) {
Serial.println("OSC did not start.");
}
delay( 200 );
Hid.SetReportParser(0, &Parser);
}
void loop() {
Usb.Task();
} </c>
APR標籤
<vb> Combine('*', if(Position(加工設計書標籤.長度, 'M', 0)>0,Replace(加工設計書標籤.長度,Position(加工設計書標籤.長度, 'M', 0),1),加工設計書標籤.長度), '*') </vb>
- 條碼字型 C39P48DITt(無顯示文字)
零件清單
- Arduino Mega 2560:280元
- Arduino USB Host Shield:260元
- 32x16 RGB LED Matrix:1050元
- 5M 300LED WS2812B 5050SMDx4=20M:2540
- LED 電源變壓器5V 50W:500元
- DENSO QK30-U Series 桌上型條碼掃描器:3500元
- 總計 8,130元
- 24L01無線模組轉接板 3.3V:20元x2
- NORDIC原裝NRF24L01+ PA LNA的無線模塊:130x2
- MW明緯原裝LRS-50-5電源供應器/變壓器(5V 10A 50W):375元
- Arduino UNO R3、Mega328+ ATMega16U2:185元
- Arduino USB Host Shield:260元
- 保護盒 90+130=220元
- 杜邦連接糸線 60元
- 總計1400元
工程需求
- 桌面部分
- 條碼掃瞄器安裝 : 桌面挖洞與桌面齊平
- 固定桌腳 : 避免桌子移動,扯壞LED燈條
- 綠墊割開 10mm寬 : 避免燈條被壓壞
- 燈條電源孔 : 燈條安裝於距桌端面3cm,需挖孔穿電源線
- 桌面控制器安裝
- 電源供應器安裝 : 要注意燈條電源線長
- LED看板
- LED看板固定
- 看板控制器固定
- 看板電源供應器固定
- 看板接線方法
- 電源插座及開關(或插拔插頭)
- 桌面電源 : 一桌至少三孔插座
- 看板電源 : 一桌至少三孔插座