檢視 裁線條碼亮燈 的原始碼
←
裁線條碼亮燈
跳至導覽
跳至搜尋
由於以下原因,您無權編輯此頁面:
您請求的操作只有這個群組的使用者能使用:
使用者
您可以檢視並複製此頁面的原始碼。
==20200604看板== <c> //接收及LED看板 //20200604以pi send to Arduino uno //20190221增加經過10分鐘看板未輸入條碼,LED看板全黑 #include <SPI.h> #include <RF24.h> #include <Adafruit_GFX.h> // Core graphics library #include <RGBmatrixPanel.h> // Hardware-specific library #define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega) #define LAT A3 #define OE 9 #define A A0 #define B A1 #define C A2 RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false); RF24 rf24(A4, A5); // CE腳, CSN腳 const uint64_t addr = 0xF0F0F0F0E2LL; const uint64_t pipe = 0xE8E8F0F0E2LL; void setup() { Serial.begin(9600); rf24.begin(); matrix.begin(); rf24.setChannel(0x72); // 設定頻道編號 rf24.setPALevel(RF24_PA_MAX); rf24.setDataRate(RF24_1MBPS); rf24.openReadingPipe(1, pipe); // 開啟通道和位址 rf24.enableDynamicPayloads(); rf24.powerUp(); rf24.startListening(); // 開始監聽無線廣播 matrix.fillScreen(matrix.Color333(0, 0, 0)); matrix.setTextColor(matrix.Color333(7,0,0)); matrix.setCursor(8, 4); matrix.print("TSK"); } unsigned long starttime; unsigned long runtime; void loop() { starttime = millis()/60000; if (rf24.available()) { char msg[32] = ""; //char s[10]; runtime = millis()/60000; rf24.read(&msg, sizeof(msg)); String myString = String(msg); int sX=(myString.length() >=5)? 1:5 ; matrix.setCursor(sX, 1); matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black' //線長大於等於10紅色,小於10橙色 if(atof(msg)<3){ matrix.setTextColor(matrix.Color333(0,7,3)); }else if(atof(msg)>=3 && atof(msg)<10){ matrix.setTextColor(matrix.Color333(7,3,0)); }else{ matrix.setTextColor(matrix.Color333(7,0,0)); } delay(30); matrix.setTextSize(1); matrix.print(myString); matrix.setCursor(25, 8); matrix.setTextColor(matrix.Color333(0,7,0)); matrix.print("m"); Serial.println(myString); } //超過10分鐘沒有輸入條碼,則關閉LED看板 if((starttime-runtime)>=10){ matrix.fillScreen(matrix.Color333(0, 0, 0)); } //Serial.println(starttime-runtime); delay(300); } </c> ==20190320看板*2== <c> //接收及LED看板 //20190221增加經過10分鐘看板未輸入條碼,LED看板全黑 #include <SPI.h> #include "RF24.h" #include <Adafruit_GFX.h> // Core graphics library #include <RGBmatrixPanel.h> // Hardware-specific library #define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega) #define LAT A3 #define OE 9 #define A A0 #define B A1 #define C A2f #define n 2 // inline panels number RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false,32*n); RF24 rf24(A4, A5); // CE腳, CSN腳 const byte addr[] = "1Node"; const byte pipe = 1; // 指定通道編號 void setup() { Serial.begin(9600); rf24.begin(); matrix.begin(); rf24.setChannel(76); // 設定頻道編號 rf24.setPALevel(RF24_PA_MAX); rf24.setDataRate(RF24_250KBPS); rf24.openReadingPipe(pipe, addr); // 開啟通道和位址 rf24.startListening(); // 開始監聽無線廣播 matrix.fillScreen(matrix.Color333(0, 0, 0)); matrix.setTextColor(matrix.Color333(7,0,0)); matrix.setCursor(8, 4); matrix.print("TSK"); } unsigned long starttime; unsigned long runtime; void loop() { starttime = millis()/60000; if (rf24.available(&pipe)) { char msg[32] = ""; //char s[10]; runtime = millis()/60000; rf24.read(&msg, sizeof(msg)); String myString = String(msg); int sX=(myString.length() >=5)? 1:5 ; matrix.setCursor(sX, 1); matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black' //線長大於等於10紅色,小於10橙色 if(atof(msg)<3){ matrix.setTextColor(matrix.Color333(0,7,3)); }else if(atof(msg)>=3 && atof(msg)<10){ matrix.setTextColor(matrix.Color333(7,3,0)); }else{ matrix.setTextColor(matrix.Color333(7,0,0)); } delay(30); matrix.setTextSize(2); matrix.print(myString); matrix.setCursor(25, 8); matrix.setTextColor(matrix.Color333(0,7,0)); matrix.print("m"); Serial.println(myString); } //超過10分鐘沒有輸入條碼,則關閉LED看板 if((starttime-runtime)>=10){ matrix.fillScreen(matrix.Color333(0, 0, 0)); } //Serial.println(starttime-runtime); delay(300); } </c> ==20190222看板== <c> //接收及LED看板 //20190221增加經過10分鐘看板未輸入條碼,LED看板全黑 #include <SPI.h> #include "RF24.h" #include <Adafruit_GFX.h> // Core graphics library #include <RGBmatrixPanel.h> // Hardware-specific library #define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega) #define LAT A3 #define OE 9 #define A A0 #define B A1 #define C A2 RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false); RF24 rf24(A4, A5); // CE腳, CSN腳 const byte addr[] = "1Node"; const byte pipe = 1; // 指定通道編號 void setup() { Serial.begin(9600); rf24.begin(); matrix.begin(); rf24.setChannel(76); // 設定頻道編號 rf24.setPALevel(RF24_PA_MAX); rf24.setDataRate(RF24_250KBPS); rf24.openReadingPipe(pipe, addr); // 開啟通道和位址 rf24.startListening(); // 開始監聽無線廣播 matrix.fillScreen(matrix.Color333(0, 0, 0)); matrix.setTextColor(matrix.Color333(7,0,0)); matrix.setCursor(8, 4); matrix.print("TSK"); } unsigned long starttime; unsigned long runtime; void loop() { starttime = millis()/60000; if (rf24.available(&pipe)) { char msg[32] = ""; //char s[10]; runtime = millis()/60000; rf24.read(&msg, sizeof(msg)); String myString = String(msg); int sX=(myString.length() >=5)? 1:5 ; matrix.setCursor(sX, 1); matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black' //線長大於等於10紅色,小於10橙色 if(atof(msg)<3){ matrix.setTextColor(matrix.Color333(0,7,3)); }else if(atof(msg)>=3 && atof(msg)<10){ matrix.setTextColor(matrix.Color333(7,3,0)); }else{ matrix.setTextColor(matrix.Color333(7,0,0)); } delay(30); matrix.setTextSize(1); matrix.print(myString); matrix.setCursor(25, 8); matrix.setTextColor(matrix.Color333(0,7,0)); matrix.print("m"); Serial.println(myString); } //超過10分鐘沒有輸入條碼,則關閉LED看板 if((starttime-runtime)>=10){ matrix.fillScreen(matrix.Color333(0, 0, 0)); } //Serial.println(starttime-runtime); delay(300); } </c> ==20190223== <c> //發送,LED燈條及條碼掃瞄 //20190220增加LED燈條後移長度 //20190222修改燈條後移長度0.3m //修改loop判斷條件的延時時間 #include <SPI.h> #include "RF24.h" #include <printf.h> #include <usbhid.h> #include <usbhub.h> #include <hiduniversal.h> #include <hidboot.h> #include <FastLED.h> #define NUM_LEDS 1200 // led灯数量20m*60顆 #define DATA_PIN A5 // 数据传输引脚(Digital 6) #define BRIGHTNESS 20 //設定led亮度 #define FRONT_LENGTH 0.295 //LED燈條後移長度 unsigned long starttime; unsigned long runtime; int ck_delay; RF24 rf24(A0, A1); // CE腳, CSN腳 const byte addr[] = "1Node"; String s; CRGB leds[NUM_LEDS]; class MyParser : public HIDReportParser { public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished(); }; MyParser::MyParser() {} void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) { // If error or empty, return if (buf[2] == 1 || buf[2] == 0) return; for (uint8_t i = 7; i >= 2; i--) { // If empty, skip if (buf[i] == 0) continue; // If enter signal emitted, scan finished if (buf[i] == UHS_HID_BOOT_KEY_ENTER) { OnScanFinished(); } // If not, continue normally else { // If bit position not in 2, it's uppercase words OnKeyScanned(i > 2, buf, buf[i]); } return; } } uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) { // Letters if (VALUE_WITHIN(key, 0x04, 0x1d)) { if (upper) return (key - 4 + 'A'); else return (key - 4 + 'a'); } // Numbers else if (VALUE_WITHIN(key, 0x1e, 0x27)) { return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1'); } if(key== 55 ) { return 46; }else return 0; } void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) { uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(50); s=(ascii==0)? s : s+ (char)ascii ; ck_delay=0; } void MyParser::OnScanFinished() { //int i,k,j=2; float a=s.toFloat(); char msg[32]; ck_delay=1; s.toCharArray(msg,32); a=(a-FRONT_LENGTH)*60; int uplimit=ceil(a); int downlimit=floor(a); delay(150); rf24.write(&msg, sizeof(msg)); // 傳送資料 runtime = millis()/60000; FastLED.clear(); delay(30); if(uplimit==downlimit){ leds[uplimit] = CRGB::White; }else{ leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red } FastLED.show(); s=""; } USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser; void setup() { FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯 FastLED.setBrightness( BRIGHTNESS ); Serial.begin( 9600 ); // Serial.println("Start"); printf_begin(); rf24.begin(); rf24.setChannel(76); // 設定頻道編號 rf24.openWritingPipe(addr); // 設定通道位址 rf24.setPALevel(RF24_PA_MAX); // 設定廣播功率 rf24.setDataRate(RF24_250KBPS); // 設定傳輸速率 rf24.stopListening(); // 停止偵聽;設定成發射模式 //rf24.printDetails(); if (Usb.Init() == -1) { Serial.println("OSC did not start."); } delay( 50 ); Hid.SetReportParser(0, &Parser); FastLED.clear(); FastLED.show(); } void loop() { starttime = millis()/60000; Usb.Task(); //十五分鐘入輸入條碼,關閉led燈條 if((starttime-runtime)>=15){ FastLED.clear(); FastLED.show(); } if(ck_delay==1)delay(200); } </c> ==20190221== <c> //接收及LED看板 //20190221增加經過10分鐘看板未輸入條碼,LED看板全黑 #include <SPI.h> #include "RF24.h" #include <Adafruit_GFX.h> // Core graphics library #include <RGBmatrixPanel.h> // Hardware-specific library #define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega) #define LAT A3 #define OE 9 #define A A0 #define B A1 #define C A2 RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false); RF24 rf24(A4, A5); // CE腳, CSN腳 const byte addr[] = "1Node"; const byte pipe = 1; // 指定通道編號 void setup() { Serial.begin(9600); rf24.begin(); matrix.begin(); rf24.setChannel(76); // 設定頻道編號 rf24.setPALevel(RF24_PA_MAX); rf24.setDataRate(RF24_250KBPS); rf24.openReadingPipe(pipe, addr); // 開啟通道和位址 rf24.startListening(); // 開始監聽無線廣播 matrix.fillScreen(matrix.Color333(0, 0, 0)); matrix.setTextColor(matrix.Color333(7,4,0)); matrix.setCursor(8, 4); matrix.print("TSK"); } unsigned long starttime; unsigned long runtime; void loop() { starttime = millis()/60000; if (rf24.available(&pipe)) { char msg[32] = ""; //char s[10]; runtime = millis()/60000; rf24.read(&msg, sizeof(msg)); String myString = String(msg); int sX=(myString.length() >=5)? 1:5 ; matrix.setCursor(sX, 1); matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black' //線長大於等於10紅色,小於10橙色 if(atof(msg)<3){ matrix.setTextColor(matrix.Color333(0,7,7)); }else if(atof(msg)>=3 && atof(msg)<10){ matrix.setTextColor(matrix.Color333(7,3,0)); }else{ matrix.setTextColor(matrix.Color333(7,0,0)); } delay(30); matrix.setTextSize(1); matrix.print(myString); matrix.setCursor(25, 8); matrix.setTextColor(matrix.Color333(0,7,0)); matrix.print("m"); Serial.println(myString); } //超過10分鐘沒有輸入條碼,則關閉LED看板 if((starttime-runtime)>=10){ matrix.fillScreen(matrix.Color333(0, 0, 0)); } //Serial.println(starttime-runtime); delay(300); } </c> <c> //發送,LED燈條及條碼掃瞄 //20190220增加LED燈條後移長度 #include <SPI.h> #include "RF24.h" #include <printf.h> #include <usbhid.h> #include <usbhub.h> #include <hiduniversal.h> #include <hidboot.h> #include <FastLED.h> #define NUM_LEDS 1200 // led灯数量20m*60顆 #define DATA_PIN A5 // 数据传输引脚(Digital 6) #define BRIGHTNESS 18 //設定led亮度 #define FRONT_LENGTH 0.3 //LED燈條後移長度 unsigned long starttime; unsigned long runtime; RF24 rf24(A0, A1); // CE腳, CSN腳 const byte addr[] = "1Node"; String s; CRGB leds[NUM_LEDS]; class MyParser : public HIDReportParser { public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished(); }; MyParser::MyParser() {} void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) { // If error or empty, return if (buf[2] == 1 || buf[2] == 0) return; for (uint8_t i = 7; i >= 2; i--) { // If empty, skip if (buf[i] == 0) continue; // If enter signal emitted, scan finished if (buf[i] == UHS_HID_BOOT_KEY_ENTER) { OnScanFinished(); } // If not, continue normally else { // If bit position not in 2, it's uppercase words OnKeyScanned(i > 2, buf, buf[i]); } return; } } uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) { // Letters if (VALUE_WITHIN(key, 0x04, 0x1d)) { if (upper) return (key - 4 + 'A'); else return (key - 4 + 'a'); } // Numbers else if (VALUE_WITHIN(key, 0x1e, 0x27)) { return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1'); } if(key== 55 ) { return 46; }else return 0; } void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) { uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(50); s=(ascii==0)? s : s+ (char)ascii ; } void MyParser::OnScanFinished() { int i,k,j=2; float a=s.toFloat(); char msg[32]; s.toCharArray(msg,32); a=(a-FRONT_LENGTH)*60; int uplimit=ceil(a)-1; int downlimit=floor(a)-1; delay(150); rf24.write(&msg, sizeof(msg)); // 傳送資料 runtime = millis()/60000; Serial.println(s); FastLED.clear(); delay(30); if(uplimit==downlimit){ leds[uplimit] = CRGB::White; }else{ leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red } FastLED.show(); s=""; } USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser; void setup() { FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯 FastLED.setBrightness( BRIGHTNESS ); Serial.begin( 9600 ); // Serial.println("Start"); printf_begin(); rf24.begin(); rf24.setChannel(76); // 設定頻道編號 rf24.openWritingPipe(addr); // 設定通道位址 rf24.setPALevel(RF24_PA_MAX); // 設定廣播功率 rf24.setDataRate(RF24_250KBPS); // 設定傳輸速率 rf24.stopListening(); // 停止偵聽;設定成發射模式 rf24.printDetails(); if (Usb.Init() == -1) { Serial.println("OSC did not start."); } delay( 50 ); Hid.SetReportParser(0, &Parser); } void loop() { starttime = millis()/60000; Usb.Task(); //十五分鐘入輸入條碼,關閉led燈條 if((starttime-runtime)>=15){ FastLED.clear(); FastLED.show(); } delay(2); } </c> ==20190117== <c> //20190124 修正桌上型掃瞄器C39 barcod前後置0的轉碼誤判 //s=(ascii==0)? s : s+ (char)ascii ; //20190117 改用Arduino Mega2560 #include <usbhid.h> #include <usbhub.h> #include <hiduniversal.h> #include <hidboot.h> #include <SPI.h> #include <FastLED.h> #include <Adafruit_GFX.h> // Core graphics library #include <RGBmatrixPanel.h> // Hardware-specific library #define NUM_LEDS 1200 // led灯数量20m*60顆 #define DATA_PIN A5 // 数据传输引脚(Digital 6) #define BRIGHTNESS 20 //設定led亮度 #define CLK 11 // MUST be on PORTB! (Use pin 11 on Mega) #define LAT A4 #define OE 9 #define A A0 #define B A1 #define C A2 //int LIGHTDELAY= 1/NUM_LEDS; String s; CRGB leds[NUM_LEDS]; RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false); class MyParser : public HIDReportParser { public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished(); }; MyParser::MyParser() {} void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) { // If error or empty, return if (buf[2] == 1 || buf[2] == 0) return; for (uint8_t i = 7; i >= 2; i--) { // If empty, skip if (buf[i] == 0) continue; // If enter signal emitted, scan finished if (buf[i] == UHS_HID_BOOT_KEY_ENTER) { OnScanFinished(); } // If not, continue normally else { // If bit position not in 2, it's uppercase words OnKeyScanned(i > 2, buf, buf[i]); } return; } } uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) { // Letters if (VALUE_WITHIN(key, 0x04, 0x1d)) { if (upper) return (key - 4 + 'A'); else return (key - 4 + 'a'); } // Numbers else if (VALUE_WITHIN(key, 0x1e, 0x27)) { return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1'); } if(key== 55 ) { return 46; }else return 0; } void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) { uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(50); s=(ascii==0)? s : s+ (char)ascii ; } void MyParser::OnScanFinished() { int i,k,j=2; float a=s.toFloat(); a=a*60; int uplimit=ceil(a)-1; int downlimit=floor(a)-1; int sX=(s.length()>=5)? 1:5 ; matrix.setCursor(sX, 1); matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black' matrix.setTextColor(matrix.Color333(7,0,0)); delay(30); matrix.setTextSize(1); Serial.println(s); matrix.print(s); FastLED.clear(); /* int delaynum= ceil(downlimit/60.0)*3; //Serial.println(delaynum); for(i=0;i< downlimit;i+=delaynum){ leds[i] = CRGB::Yellow; FastLED.show(); // delay(1); leds[i] = CRGB::Black; FastLED.show(); } */ delay(30); if(uplimit==downlimit){ leds[uplimit] = CRGB::White; }else{ leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red } FastLED.show(); matrix.setCursor(25, 8); matrix.setTextColor(matrix.Color333(0,7,0)); matrix.print("m"); s=""; } USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser; void setup() { FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯 FastLED.setBrightness( BRIGHTNESS ); matrix.begin(); Serial.begin( 115200 ); Serial.println("Start"); if (Usb.Init() == -1) { Serial.println("OSC did not start."); } delay( 100 ); Hid.SetReportParser(0, &Parser); matrix.fillScreen(matrix.Color333(0, 0, 0)); } void loop() { Usb.Task(); } </c> ==20190115== <c> //20190115 增加LED看板顯示 #include <usbhid.h> #include <usbhub.h> #include <hiduniversal.h> #include <hidboot.h> #include <SPI.h> #include <FastLED.h> #include <Adafruit_GFX.h> // Core graphics library #include <RGBmatrixPanel.h> // Hardware-specific library #define NUM_LEDS 60 // led灯数量20m*60顆 #define DATA_PIN A5 // 数据传输引脚(Digital 6) #define BRIGHTNESS 25 //設定led亮度 #define CLK 8 // MUST be on PORTB! (Use pin 11 on Mega) #define LAT A3 #define OE 9 #define A A0 #define B A1 #define C A2 //int LIGHTDELAY= 1/NUM_LEDS; String s; CRGB leds[NUM_LEDS]; RGBmatrixPanel matrix(A, B, C, CLK, LAT, OE, false); class MyParser : public HIDReportParser { public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished(); }; MyParser::MyParser() {} void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) { // If error or empty, return if (buf[2] == 1 || buf[2] == 0) return; for (uint8_t i = 7; i >= 2; i--) { // If empty, skip if (buf[i] == 0) continue; // If enter signal emitted, scan finished if (buf[i] == UHS_HID_BOOT_KEY_ENTER) { OnScanFinished(); } // If not, continue normally else { // If bit position not in 2, it's uppercase words OnKeyScanned(i > 2, buf, buf[i]); } return; } } uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) { // Letters if (VALUE_WITHIN(key, 0x04, 0x1d)) { if (upper) return (key - 4 + 'A'); else return (key - 4 + 'a'); } // Numbers else if (VALUE_WITHIN(key, 0x1e, 0x27)) { return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1'); } if(key== 55 ) { return 46; }else return 0; } void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) { uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(100); s= s + ((char)ascii) + ""; } void MyParser::OnScanFinished() { int i,k,j=2; float a=s.toFloat(); a=a*60; int uplimit=ceil(a)-1; int downlimit=floor(a)-1; matrix.setCursor(5, 0); matrix.fillScreen(matrix.Color333(0, 0, 0)); // fill the screen with 'black' matrix.setTextColor(matrix.Color333(7,0,0)); delay(30); matrix.setTextSize(1); matrix.print(s); FastLED.clear(); /* int delaynum= ceil(downlimit/60.0); for(i=1;i< downlimit;i+=delaynum){ leds[i] = CRGB::Yellow; FastLED.show(); delay(10); FastLED.clear(); } */ delay(30); if(uplimit==downlimit){ leds[uplimit] = CRGB::White; }else{ leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red } FastLED.show(); matrix.setCursor(25, 7); matrix.setTextColor(matrix.Color333(0,7,0)); matrix.print("m"); s=""; } USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser; void setup() { FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯 FastLED.setBrightness( BRIGHTNESS ); matrix.begin(); Serial.begin( 115200 ); Serial.println("Start"); if (Usb.Init() == -1) { Serial.println("OSC did not start."); } delay( 100 ); Hid.SetReportParser(0, &Parser); matrix.fillScreen(matrix.Color333(0, 0, 0)); } void loop() { Usb.Task(); } </c> ==20190104-2== <c> //20190104增加LCD顯示 #include <Wire.h> #include <LiquidCrystal_I2C.h> #include <usbhid.h> #include <usbhub.h> #include <hiduniversal.h> #include <hidboot.h> #include <SPI.h> #include <FastLED.h> #define NUM_LEDS 60 // led灯数量 #define DATA_PIN 6 // 数据传输引脚(Digital 6) #define BRIGHTNESS 25 //設定led亮度 int LIGHTDELAY= 60/NUM_LEDS/60; String s; CRGB leds[NUM_LEDS]; LiquidCrystal_I2C lcd(0x27,20,4); // set the LCD address to 0x27 for a 16 chars and 2 line display class MyParser : public HIDReportParser { public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished(); }; MyParser::MyParser() {} void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) { // If error or empty, return if (buf[2] == 1 || buf[2] == 0) return; for (uint8_t i = 7; i >= 2; i--) { // If empty, skip if (buf[i] == 0) continue; // If enter signal emitted, scan finished if (buf[i] == UHS_HID_BOOT_KEY_ENTER) { OnScanFinished(); } // If not, continue normally else { // If bit position not in 2, it's uppercase words OnKeyScanned(i > 2, buf, buf[i]); } return; } } uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) { // Letters if (VALUE_WITHIN(key, 0x04, 0x1d)) { if (upper) return (key - 4 + 'A'); else return (key - 4 + 'a'); } // Numbers else if (VALUE_WITHIN(key, 0x1e, 0x27)) { return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1'); } if(key== 55 ) { return 46; }else return 0; } void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) { uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(100); s= s + ((char)ascii) + ""; } void MyParser::OnScanFinished() { int i,k,j=2; float a=s.toFloat(); String lcdtext2=s +" m"; lcd.clear(); lcd.setCursor(1,0); lcd.print("Cable Length:"); lcd.setCursor(6,1); lcd.print(lcdtext2); a=a*60; int uplimit=ceil(a)-1; int downlimit=floor(a)-1; FastLED.clear(); for(i=1;i< downlimit;i++){ leds[i] = CRGB::Yellow; FastLED.show(); delay(LIGHTDELAY); FastLED.clear(); } if(uplimit==downlimit){ leds[uplimit] = CRGB::White; }else{ leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red } FastLED.show(); s=""; } USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser; void setup() { FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯 FastLED.setBrightness( BRIGHTNESS ); Serial.begin( 115200 ); lcd.init(); lcd.backlight(); lcd.setCursor(1,0); lcd.print("Cable Length:"); if (Usb.Init() == -1) { Serial.println("OSC did not start."); } delay( 200 ); Hid.SetReportParser(0, &Parser); } void loop() { Usb.Task(); } </c> ==20190104-1== <c> //20190104增加流水燈 #include <usbhid.h> #include <usbhub.h> #include <hiduniversal.h> #include <hidboot.h> #include <SPI.h> #include <FastLED.h> #define NUM_LEDS 60 // led灯数量 #define DATA_PIN 6 // 数据传输引脚(Digital 6) #define BRIGHTNESS 25 //設定led亮度 int LIGHTDELAY= 60/NUM_LEDS/60; String s; CRGB leds[NUM_LEDS]; class MyParser : public HIDReportParser { public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished(); }; MyParser::MyParser() {} void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) { // If error or empty, return if (buf[2] == 1 || buf[2] == 0) return; for (uint8_t i = 7; i >= 2; i--) { // If empty, skip if (buf[i] == 0) continue; // If enter signal emitted, scan finished if (buf[i] == UHS_HID_BOOT_KEY_ENTER) { OnScanFinished(); } // If not, continue normally else { // If bit position not in 2, it's uppercase words OnKeyScanned(i > 2, buf, buf[i]); } return; } } uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) { // Letters if (VALUE_WITHIN(key, 0x04, 0x1d)) { if (upper) return (key - 4 + 'A'); else return (key - 4 + 'a'); } // Numbers else if (VALUE_WITHIN(key, 0x1e, 0x27)) { return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1'); } if(key== 55 ) { return 46; }else return 0; } void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) { uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(100); s= s + ((char)ascii) + ""; } void MyParser::OnScanFinished() { int i,k,j=2; float a=s.toFloat(); a=a*60; int uplimit=ceil(a)-1; int downlimit=floor(a)-1; //Serial.println(uplimit); FastLED.clear(); for(i=1;i< downlimit;i++){ leds[i] = CRGB::Yellow; FastLED.show(); delay(LIGHTDELAY); FastLED.clear(); } if(uplimit==downlimit){ leds[uplimit] = CRGB::White; }else{ leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red } FastLED.show(); s=""; } USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser; void setup() { FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯 FastLED.setBrightness( BRIGHTNESS ); Serial.begin( 115200 ); Serial.println("Start"); if (Usb.Init() == -1) { Serial.println("OSC did not start."); } delay( 200 ); Hid.SetReportParser(0, &Parser); } void loop() { Usb.Task(); } </c> ==20190103== <c> #include <usbhid.h> #include <usbhub.h> #include <hiduniversal.h> #include <hidboot.h> #include <SPI.h> #include <FastLED.h> #define NUM_LEDS 60 // led灯数量 #define DATA_PIN 6 // 数据传输引脚(Digital 6) #define BRIGHTNESS 25 ////設定led亮度 String s; CRGB leds[NUM_LEDS]; class MyParser : public HIDReportParser { public: MyParser(); void Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf); protected: uint8_t KeyToAscii(bool upper, uint8_t mod, uint8_t key); virtual void OnKeyScanned(bool upper, uint8_t mod, uint8_t key); virtual void OnScanFinished(); }; MyParser::MyParser() {} void MyParser::Parse(USBHID *hid, bool is_rpt_id, uint8_t len, uint8_t *buf) { // If error or empty, return if (buf[2] == 1 || buf[2] == 0) return; for (uint8_t i = 7; i >= 2; i--) { // If empty, skip if (buf[i] == 0) continue; // If enter signal emitted, scan finished if (buf[i] == UHS_HID_BOOT_KEY_ENTER) { OnScanFinished(); } // If not, continue normally else { // If bit position not in 2, it's uppercase words OnKeyScanned(i > 2, buf, buf[i]); } return; } } uint8_t MyParser::KeyToAscii(bool upper, uint8_t mod, uint8_t key) { // Letters if (VALUE_WITHIN(key, 0x04, 0x1d)) { if (upper) return (key - 4 + 'A'); else return (key - 4 + 'a'); } // Numbers else if (VALUE_WITHIN(key, 0x1e, 0x27)) { return ((key == UHS_HID_BOOT_KEY_ZERO) ? '0' : key - 0x1e + '1'); } if(key== 55 ) { return 46; }else return 0; } void MyParser::OnKeyScanned(bool upper, uint8_t mod, uint8_t key) { uint8_t ascii = KeyToAscii(upper, mod, key); // Serial.print((char)ascii); delay(100); s= s + ((char)ascii) + ""; //s=s + ascii; } void MyParser::OnScanFinished() { float a=s.toFloat(); a=a*60; int uplimit=ceil(a)-1; int downlimit=floor(a)-1; Serial.println(uplimit); FastLED.clear(); if(uplimit==downlimit){ leds[uplimit] = CRGB::White; }else{ leds[uplimit] = CRGB::Red; // 设置第1个led灯的颜色Red leds[downlimit] = CRGB::Green; // 设置第2个led灯的颜色Red } FastLED.show(); s=""; } USB Usb; USBHub Hub(&Usb); HIDUniversal Hid(&Usb); MyParser Parser; void setup() { FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); // 初始化所有LED灯 FastLED.setBrightness( BRIGHTNESS ); Serial.begin( 115200 ); Serial.println("Start"); if (Usb.Init() == -1) { Serial.println("OSC did not start."); } delay( 200 ); Hid.SetReportParser(0, &Parser); } void loop() { Usb.Task(); } </c> ==APR標籤== <vb> Combine('*', if(Position(加工設計書標籤.長度, 'M', 0)>0,Replace(加工設計書標籤.長度,Position(加工設計書標籤.長度, 'M', 0),1),加工設計書標籤.長度), '*') </vb> *條碼字型 C39P48DITt(無顯示文字) ==零件清單== *[https://goods.ruten.com.tw/item/show?21310080868502 Arduino Mega 2560]:280元 *[https://goods.ruten.com.tw/item/show?21733964944057 Arduino USB Host Shield]:260元 *[https://goods.ruten.com.tw/item/show?21646433501353 32x16 RGB LED Matrix]:1050元 *[https://shopee.tw/5M-300LED-WS2812B-5050SMD%E8%B7%91%E9%A6%AC%E7%87%88%E4%B8%B2%E5%B9%BB%E5%BD%A9%E7%87%88%E5%B8%B65V%E4%B8%8D%E9%98%B2%E6%B0%B4-i.28087237.1723413462 5M 300LED WS2812B 5050SMDx4=20M]:2540 *[https://goods.ruten.com.tw/item/show?21207103775117 LED 電源變壓器5V 50W]:500元 *[https://goods.ruten.com.tw/item/show?21823144632017 DENSO QK30-U Series 桌上型條碼掃描器]:3500元 *總計 8,130元 *[https://goods.ruten.com.tw/item/show?21646421762742 24L01無線模組轉接板 3.3V]:20元x2 *[https://shopee.tw/product/4877344/64923635 NORDIC原裝NRF24L01+ PA LNA的無線模塊]:130x2 *[https://goods.ruten.com.tw/item/show?21747360083001 MW明緯原裝LRS-50-5電源供應器/變壓器(5V 10A 50W)]:375元 *[https://goods.ruten.com.tw/item/show?21404244774414 Arduino UNO R3、Mega328+ ATMega16U2]:185元 *[https://goods.ruten.com.tw/item/show?21733964944057 Arduino USB Host Shield]:260元 *保護盒 90+130=220元 *杜邦連接糸線 60元 *總計1400元 ==工程需求== *桌面部分 **條碼掃瞄器安裝 : 桌面挖洞與桌面齊平 **固定桌腳 : 避免桌子移動,扯壞LED燈條 **綠墊割開 10mm寬 : 避免燈條被壓壞 **燈條電源孔 : 燈條安裝於距桌端面3cm,需挖孔穿電源線 **桌面控制器安裝 **電源供應器安裝 : 要注意燈條電源線長 *LED看板 **LED看板固定 **看板控制器固定 **看板電源供應器固定 *電源插座及開關(或插拔插頭) **桌面電源 : 一桌至少三孔插座 **看板電源 : 一桌至少三孔插座
返回到「
裁線條碼亮燈
」。
導覽選單
個人工具
建立帳號
登入
命名空間
頁面
討論
臺灣正體
視圖
閱讀
檢視原始碼
檢視歷史
更多
搜尋
導覽
首頁
近期變更
隨機頁面
MediaWiki說明
工具
連結至此的頁面
相關變更
特殊頁面
頁面資訊